RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 2
1
2
Search: Posts Made By: HarryC
Showing results 1 to 25 of 30
Search took 0.01 seconds.
Forum: RC Jets
09-15-2022, 12:10 PM
Replies: 554
Views: 88,470
Posted By HarryC

be sure to make the mixer curve from 0 to 100,...

be sure to make the mixer curve from 0 to 100, not the default -100 to +100, otherwise wheels up will give down trim instead of returning to neutral
Forum: RC Jets
09-15-2022, 09:47 AM
Replies: 554
Views: 88,470
Posted By HarryC

Another great new LUA app for you. Sometimes you...

Another great new LUA app for you. Sometimes you end up with batteries of different capacities for the same model, and the Alarm at some mAh count is only correct for one capacity. Or you have some...
Forum: RC Jets
09-14-2022, 11:26 PM
Replies: 554
Views: 88,470
Posted By HarryC

There are choices, depends on your own...

There are choices, depends on your own preferences. Whichever you choose I strongly recommend that it blends in slowly over 1 to 2 seconds rather than instantly, a trim change like that happening...
Forum: RC Jets
07-26-2022, 01:35 PM
Replies: 554
Views: 88,470
Posted By HarryC

I used a MUI 30, with the current wire let into...

I used a MUI 30, with the current wire let into the pump wire (brushed motor, cannot do it with the newer brushless pumps) and the volts wire connected to the turbine battery. Flameout alarm if...
Forum: RC Jets
05-27-2022, 10:50 PM
Replies: 554
Views: 88,470
Posted By HarryC

Put the cursor over it and press

Put the cursor over it and press
Forum: RC Jets
02-15-2021, 02:25 PM
Replies: 554
Views: 88,470
Posted By HarryC

The whole issue has been about noise, not...

The whole issue has been about noise, not mechanical vibration in the low frequencies shown in the Assist vib analyser which is aimed at airframe vibration in the frequencies caused by piston...
Forum: RC Jets
02-14-2021, 01:58 PM
Replies: 554
Views: 88,470
Posted By HarryC

The noise of a jet engine has nothing to do with...

The noise of a jet engine has nothing to do with mechanical vibration of the engine so you cannot simply try to equate rpm to Hz. The noise is made by oscillations in the airflows. Have you never...
Forum: RC Jets
01-19-2021, 03:30 PM
Replies: 554
Views: 88,470
Posted By HarryC

MEMS gyros are prone to interference from...

MEMS gyros are prone to interference from ultrasonic sound at the high frequencies at which the gyros vibrate. It is a well known phenomenon. Totally unrelated to piston engine airframe vibration...
Forum: RC Jets
01-19-2021, 01:50 PM
Replies: 554
Views: 88,470
Posted By HarryC

CARS II, if you think you are investigating the...

CARS II, if you think you are investigating the acoustic interference problem then you are barking up the wrong tree! The problem is caused by sound waves in the ultrasonic region. The Assist...
Forum: RC Jets
11-30-2020, 10:02 PM
Replies: 554
Views: 88,470
Posted By HarryC

I agree with Wayne, keep them separate.

I agree with Wayne, keep them separate.
Forum: RC Jets
11-12-2020, 04:24 AM
Replies: 554
Views: 88,470
Posted By HarryC

I have just had a play with the Assist, it is...

I have just had a play with the Assist, it is clever enough to recognise the difference between aileron control and flaperon control, so even at 100% flaperon travel it does not apply the stick...
Forum: RC Jets
11-03-2020, 11:45 PM
Replies: 554
Views: 88,470
Posted By HarryC

You only need to add 2 flight modes, just use...

You only need to add 2 flight modes, just use default as one of your modes
Forum: RC Jets
09-18-2020, 07:03 AM
Replies: 554
Views: 88,470
Posted By HarryC

If I need to stick it to bare wood I have in the...

If I need to stick it to bare wood I have in the past just treated the wood (even balsa wood) with warmed 30 minute epoxy so it flows to a smooth, flat surface, then cleaned with alcohol when it is...
Forum: RC Jets
09-17-2020, 09:31 PM
Replies: 554
Views: 88,470
Posted By HarryC

As much as possible, you should only use the...

As much as possible, you should only use the double sided tape to mount a gyro. This is in the instructions of every brand of gyro, not just Assist. Do not use hard mounts, clips, velcro straps...
Forum: RC Jets
09-16-2020, 12:17 AM
Replies: 554
Views: 88,470
Posted By HarryC

Sadly, the Assist gyro is getting a lot of...

Sadly, the Assist gyro is getting a lot of reports of acoustic interference from jet engines. You should ground test it before flying. With the engine running, switch the gyro on, turn up the gain,...
Forum: RC Jets
09-04-2020, 10:16 AM
Replies: 554
Views: 88,470
Posted By HarryC

yes of course

yes of course
Forum: RC Jets
09-03-2020, 09:34 PM
Replies: 554
Views: 88,470
Posted By HarryC

If you have created a steering function then it...

If you have created a steering function then it has all the software it needs to control it. Mixing rudder to it is unnecessary and is a hangover from the JR/Futaba way of thinking.
Forum: RC Jets
08-29-2020, 12:54 PM
Replies: 554
Views: 88,470
Posted By HarryC

https://youtu.be/ww6WhsvXrWw

https://youtu.be/ww6WhsvXrWw
Forum: RC Jets
08-19-2020, 01:52 PM
Replies: 554
Views: 88,470
Posted By HarryC

You have got that wrong, simply switching it off...

You have got that wrong, simply switching it off or disconnecting the battery, unlocks it.
Forum: RC Jets
08-18-2020, 10:49 PM
Replies: 554
Views: 88,470
Posted By HarryC

Please be careful with the use of the phrase...

Please be careful with the use of the phrase "flight modes". In several of the posts above people are confusing Tx flight modes and Assist gyro modes because the one phrase "flight mode" is being...
Forum: RC Jets
08-18-2020, 10:41 PM
Replies: 554
Views: 88,470
Posted By HarryC

I recommend that you do not use the Tx Gyro...

I recommend that you do not use the Tx Gyro function with Assist. The gyro functions were not designed for Assist and need to be re-written by Jeti to work properly with Assist. The gyro function...
Forum: RC Jets
08-17-2020, 01:56 PM
Replies: 554
Views: 88,470
Posted By HarryC

That makes sense Wayne, I had thought you meant...

That makes sense Wayne, I had thought you meant that you were increasing the normal (or full rate) travel.
Forum: RC Jets
08-16-2020, 09:24 PM
Replies: 554
Views: 88,470
Posted By HarryC

Double post

Double post
Forum: RC Jets
08-16-2020, 09:24 PM
Replies: 554
Views: 88,470
Posted By HarryC

No, it was bad because it was too responsive....

No, it was bad because it was too responsive. Jeti was badly advised and they made the Assist into a flight controller, not a traditional gyro. It took over the controls and moved the surfaces far...
Forum: RC Jets
08-12-2020, 12:54 PM
Replies: 554
Views: 88,470
Posted By HarryC

A gyro does not care where it is placed in a...

A gyro does not care where it is placed in a rigid body. However, an accelerometer does care, and the Assist uses both. Hence Jeti's instruction to mount the Assist near the CG. We don't know what...
Showing results 1 to 25 of 30
 
Page 1 of 2
1
2


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.